The Warm Audio Centavo is an accurate recreation of the most sought-after overdrive pedal of the 90's and beyond. Whether you're after the fabled clean boost tones, transparent overdrive, or you want to push your dirty channels to true grit, the Centavo has all of the adored tones of the vintage box. In addition, the Warm Audio Centavo has the infamous “MOD” selectable on the back. When in the “up” position, low-end response on the bottom strings is extended. With a true-to-original, custom-cast golden enclosure & all the signature sounds of the original, Centavo delivers an authentically legendary pedal experience.
MORE»
| Price | $179.00 |
The Tensor(TM) gives you live reverse and tape stop effects, pitch shifting, time stretching and hold functions that you can combine in creative ways. Slow down, speed up and rewind in real time. Stretch or compress time with no pitch change. Loop, overdub, and randomly slice phrases up to 9.4 seconds (4.7 seconds in stereo).
Intelligent randomization adapts to the knob settings. The results range from occasional CD skips, stutters, and rhythmic repeats to random slicing and erratic pitch shifts. Both foot switches have momentary and latching modes to inject pitch jumps, glitches, or instantly rewind what you just played.
The Tensor(TM) is in a pedalboard-friendly enclosure with all jacks on top. All controls are immediately accessible with well-spaced knobs for live tweaking, and USB MIDI for recording and sequencing.
Features:
• Tape speed from reverse to stop to forward
• Realtime time stretch up to 4:1
• Loop time compression and stretch from 1:4 to 4:1
• Pitch shift from -2 to +2 octaves
• Intelligent randomization
• Overdub, replace, and dual buffer (next) loop modes
• Forward/alternate/reverse loop direction
• Additional looping functions via remote switch or MIDI
• Momentary or latching foot switches
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• +5.5 dBu maximum input level (adjustable to +8 dBu)
• Stereo input/output (TRS)
• MIDI (USB and TRS)
• Web-based editor for editing presets and accessing hidden parameters
MORE»
| Price | $329.00 |
Particle™ is a granular delay/pitch shifting pedal. It chops your signal into small grains and then rearranges, shifts, and mangles it, using the techniques of granular synthesis in real time. Results range from radical pitch and delay modulation to shimmering repeats to time stretching, stutter, and glitch sounds.
Five delay and three pitch modes give intuitive control over random delays, bubbling textures, time stretching, and rhythmic glitches. Take a unique approach beyond conventional delay, pitch, flanging, and chorus sounds. Freeze notes with adjustable threshold for stutter, punch in, or drone-line effects. Lock multiple parameters to tap tempo or MIDI sync with independent note divisions for intricate rhythms. Access all parameters via MIDI, tablet, or “modeless” front-panel operation for full control over granular processing.
The Particle 2 is performance friendly, with controls spaced for real-time tweaking and designed so you can explore new sonic territory while remaining in control. Use the assignable expression pedal or DIY-friendly remote switch for hands-free control. The Particle 2 is pedalboard-friendly with all jacks on top. With full MIDI control, stereo input/output, and +8 dBu maximum input level, it is also at home in modular setups or the studio.
Features:
• 3 pitch modes: detune, density, LFO
• 5 delay modes: random, density, LFO, random pitch, reverse
• Adjustable grain size and density
• Pitch shift +/- 1 octave
• Delay 0-2.5 seconds
• Feedback with adjustable lowpass filter
• Auto-freeze/stutter with adjustable threshold
• Tap tempo/momentary freeze footswitch
• Independent tap divisions for delay time, grain size, grain density, and LFO
• Soft touch bypass (momentary or latching), user replaceable
• Stereo input/output (TRS)
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• Additional parameters via MIDI (USB or TRS)
• MIDI clock synchronization
• Presets (4 on front, 127 via MIDI)
• Web-based editor for editing presets and accessing hidden parameters
Designed and assembled in USA. Requires a 9V 250 mA center negative power supply (not included).
MORE»
| Price | $329.00 |
The Warmdrive is a true reproduction of a highly revered pedal known for delivering the tones of an unattainable overdriven amp. The original pedal is known to go from silky-smooth tones reminiscent of a special overdriven amp at the sweet spot, all the way to sustain-rich distortion. The Warmdrive combines carefully-selected components & true-to-original circuit design to achieve the same tone and sonic profile of the legendary pedal. The “secret sauce” of the Warmdrive, just like the original, is the unique voice/tone control combination on the stomp box. Giving artists extra versatility, this control allows the player to modify the frequency both before (Voice control) and after (Tone control) the clipping stages.
MORE»
| Price | $149.00 |
The Next Gen of a Classic
Soul Press II is a next-gen product in the Hotone Press series pedal line. It's new-designed upgrade based on the popular concepts of both the Soul Press and Vow Press. It integrates up to four function modes (volume, wah, volume/wah, expression), taking playability to new heights. The pedal position indicator shows the pedal position in real time. The TONE mode selection and Q value adjustment represent an absolute improvement in tone and functionality. Multiple I/O options provide more diverse access. The reimagined pedal size maintains portability while delivering an optimal ergonomic experience. Soul Press II is a truly versatile wah pedal.
MORE»
| Price | $119.99 |
Pro level quality at an entry level price. The new Mini Classic Switchless Wah comes equipped with the great features our Wah pedals are known for, all for just $99. Yes, you read that correctly! Just $99. You get classic Wah-Wah tone with our MQ2 Inductor, dependable Electro-Optical circuitry, smooth and easy Switchless activation, and our True Tone Bypass Buffer circuitry.
Features include:
• Switchless operation – simply step on the treadle to engage the Wah and step off to bypass
• Engineered to save space on your board
• World famous Electro-Optical design
• Classic Wah tone with a custom MQ2 Inductor
• True Tone Bypass buffer circuit ensures pure guitar tone and output
• Glow-in-the-dark treadle rubber and Morley logo
• Powered by one 9-volt battery or optional Morley 9V adapter
• Rugged cold-rolled steel housing, LED indication, quick clip battery door and one-year warranty
• Works with Guitar, Bass or Keys
MORE»
| List | $129.00 |
| Price | $116.10 (Save: $12.90) |
The hard-clipping, op-amp-based circuit of the ODD (Over Drive Disorder) delivers all of the sounds of a cranked, saturated tube amp made famous in legendary recordings. True to its inspiration, the ODD is perfect for adding a little breakup to an otherwise clean tone, or dramatically transforming your clean pedal-platform amp into a punk-rock powerhouse. To accurately deliver this popular modern tone, the ODD is built like an iconic pedalboard staple with through-hole construction using premium components, including a TLO82CP Op-Amp, 2N7000 transistors, & hand-selected capacitors & resistors.
Featuring classic-inspired controls & sounds, including a UK/US Switch, the ODD can quickly flip personalities. Engaging the UK setting distorts earlier, bumps the upper-mids, and increases volume – giving this setting more of a cranked, “chimey” amplifier tone. The US setting has a little more clean headroom, allowing the ODD to act more like a boost at first, and better aligns with traditional tweed-based “edge of breakup” amplifier tones.
MORE»
| Price | $119.00 |
The Warm Audio Mutation Phasor II is an accurate recreation of a swirly phaser made famous in the experimental era of the 1970s. Mutation Phasor II has all of the vintage vibes of the original phaser pedal allowing you to add depth, wobble, swirl, or “instant funk” to guitar, keys, bass, or anything you can dream of. This electro-optical phase-shifting pedal is built with a true-to-original recreation of the 70s circuit using premium components. True to the original pedal, Mutation Phasor II delivers all the rich depth and instant psychedelic tones, favored by innovative musicians and producers like Billy Corgan, Tom Bukovac, Robin Trower, and many more.
Tech Specs
• Electro-Optical Phase-Shifting Pedal With Feedback Circuit
• Phasing Rate: .1Hz - 18Hz
• Premium Components, Including RC4558P Op-Amps, Various Vintage-Style Diodes, and Hand-Selected Film Capacitors & Carbon Resistors
• Controls: Rate, Depth, and Feedback
• Frequency Response: 20Hz - 20KHz
• Min Feedback: 4V RMS, 11.2V Peak-to-Peak ¦ Max Feedback: 2V RMS, 5.6V Peak-to-Peak
• Signal-to-Noise Ratio: 86 dB Below 2V Input
• Current Draw: 150 mA
• Buffered Bypass
• 9-Volt Battery Or External 9V Regulated DC Adapter (center-negative)
Popular Uses
• Deep, Phase-Shifting Electric Guitar Tones
• Swirling, Psychedelic Modulated Keys
• Funky. “Wobbly” Base Lines
MORE»
| Price | $149.00 |
The HX Stomp XL delivers HX® modeling in a performance-ready pedal with eight capacitive-touch footswitches. The same SHARC® DSP chip found in Helix® enables it to run up to eight processing blocks simultaneously, and the footswitches let you access and control those blocks in powerful ways. It sends and receives Program Change, Continuous Controller, and other MIDI messages. USB HX Stomp XL functions as a multi-channel 24-bit/96kHz audio interface for Mac and PC, with DI, re-amping, and MIDI capabilities built in. HX Stomp XL can also record to an iPad (with optional Apple Camera Connection Kit).
MORE»
| List | $949.99 |
| Price | $854.99 (Save: $95.00) |
The first in the Mako series, the D1 is a powerful multi-function delay with five, studio grade, high-fidelity, custom tuned programs. The programs are Digital, Mod, Vintage, Dual and Reverse. Each can be tuned and tweaked with modulation, tone, age, and subdivisions. The attack knob adds another dynamic to each program, opening up a new world for creating soundscapes. The D1 boasts stereo in and out, midi control and on-board presets. A workhorse of a delay that is just as ready for the road as it is the studio.
Each program can be fully customized to your taste and playing style with the Tweak knob. Flip the toggle switch to Mod to bring in a tasteful modulation to your delay trails. Tone will brighten or darken your delay trails. Age will add some grit and wear reminiscent of vintage delay units. Subdivisions can be easily changed between quarter, eighth and dotted eighth.
The Attack knob will soften the attack of the echoes. Dreamy and ethereal soundscapes can be created with higher repeat and attack settings.
Specs:
• The D1 comes in an anodized silver finish with black, dark green, red, orange and purple ink.
• The enclosure's exact size with knobs is 4.9-inches xx 2.52-inches x 2.64-inches
• Power requirements are 9VDC (300mA minimum)
The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended. Power supply not included. MORE»
| Price | $299.00 |
HX Stomp™ is a professional-grade multi-effects processor that delivers the sound of Helix® amps, cabs, and effects in an ultra-compact pedal. Use it as a “super stompbox,” a backup or travel rig, an add-on tone expander when combined with other modelers, an audio interface – or even a complete guitar or bass rig. The same HX Modeling technology that powers the flagship Helix guitar processor enables HX Stomp to run up to six processing blocks simultaneously, making it the most powerful and flexible stompbox-sized multi-effects processor available. HX Stomp is easy to operate, however, thanks to its simple-but-powerful controls, 320 x 240-pixel color LCD, and capacitive-sensing footswitches with color-coded LED rings. External control via MIDI and optional expression pedal and footswitch control provide additional flexibility, as does I/O that may be configured for sophisticated routing such as simultaneously feeding an amp and a FOH mixer, 4-cable method operation with an amplifier, and studio re-amping. Along with over 300 amps, cabs, and effects – even a looper – HX Stomp includes a legacy library of effects from Line 6® M-Series pedals, as well as from classic Line 6 stompbox modelers such as the DL4™, MM4™, FM4™, and DM4™. There are also presets created specifically for bass players, as well as individual bass amp and cab models. The free HX Edit app offers preset librarian functionality and third-party IR loading.
• Utilizes the same HX Modeling as Helix
• Over 300 effects and models from Helix, M-Series, and legacy Line 6 products
• Up to 6 simultaneous amp, cab, and effect blocks (including a looper and IR loading)
• 3 capacitive-sensing footswitches with color-coded LED rings facilitate fast editing
• TRS dual expression pedal/footswitch input extends creative control capabilities
• Stereo effects loop (mono/stereo TRS send + stereo returns) facilitates use with other pedals
MORE»
| Price | $699.99 |
With its simple plug-and-play interface, ultra-portable lightweight design, and best-in-class tones, the POD® Go guitar processor gets you on the road to ultimate tone.
POD Go enables a simple and intuitive workflow. Choose, edit, and control sounds using the large color LCD screen, five push encoders, eight rugged footswitches, and cast-aluminum multi-function expression pedal–and add two external footswitches or a second expression pedal for even more real-time control. All the essential audio connections are at your fingertips, too, including balanced stereo outputs, a duplicate amp out that can be tapped before the Cab/IR, a stereo effects loop, a headphone jack, and even a USB port for accessing the 4-in/4-out audio interface with re-amping.
POD Go boasts an arsenal of professional-quality amp, cab, and effect models drawn from the acclaimed HX family of effects processors–including classic amps like the Blackface, Plexi Lead, and Treadplate–as well as supporting third-party IR loading. What is more, sophisticated features such as Snapshots enable you to easily access all the tones you'll need to cover every section of every song. With POD Go, you won't just take the stage–you'll own it!
• Best-in-class performance
• Simple interface with large color display
• Compact, ultra-portable lightweight design
• 270+ HX and legacy amp and effects models
• Third-party IR loading
• Stereo effects loop and Expression Pedal/Footswitch input
• Free POD Go Edit app
MORE»
| List | $669.99 |
| Price | $602.99 (Save: $67.00) |
The new Foxy Tone Box from Warm Audio is a hyper-accurate recreation of one of the most sought-after and beloved fuzz pedals of all time – used in the early seventies by legendary tone masters Billy Gibbons and Peter Frampton, and in the present day by folks like Adrian Belew, Nine Inch Nails and Beck. Covered in thick velvet just like the vintage pedal, the Warm Audio Foxy Tone Box faithfully recreates the vintage circuit and brings you the huge tone, octave-up sounds and look of the original...without having to pay crazy vintage prices!
MORE»
| Price | $149.00 |
The Raster is a 1600 ms digital delay with a pitch and frequency shifter integrated into the feedback path. Forward or reverse delay can be shifted once or have continuously shifted repeats. Three delay ranges allow you to precisely dial in resonant feedback and instantly change delay time with rhythmic shifts. The feedback control has infinite repeats at 3 o'clock and chaotic, textured feedback loops at higher levels. Knob responses are carefully tuned for exploration of self-oscillation and feedback on the verge of blowing up. A tone control sweeps from dark analog-style repeats to digital clarity and emphasizes the attack at higher settings. The left and right delay times can be set as a ratio, so a single knob changes both in sync. The two delay channels can be arranged in series, parallel or ping pong.
Three pitch and frequency shifting algorithms are integrated into the feedback loop. Pitch shifting repeats up or down in semitone steps creates tempo-synced arpeggios and alien organ sounds. The detune setting can dial in micro pitch shifts and chorused repeats. The frequency shifter creates flanger-like textures and radical dissonant echoes. The left and right channels can be shifted by the same amount, a ratio, or opposite directions. At subtle settings, repeats evolve in a way that sounds natural, but different from analog delays.
The Raster's modulation section has seven waveforms that can be assigned to delay time, pitch shift, or effect level (for tremolo). There are two random waveforms for glitchy sliced delays or random pitch shift, wow and flutter, and broken tape deck effects. Envelope and inverse envelope enable dynamic flanging and pitch bent delays. Stereo controls adjust the modulation amount and phase between channels, for subtle shifts or swirling psychedelic washes.
The Raster 2 is performance friendly, with 6 knobs and 9 switches. The original Raster was praised for its knob response and immediacy, and the Raster 2 maintains that simplicity while adding flexible modulation and extensive stereo functionality. Alternate knob settings are related to the primary knob function, labeled, and off at the center position. Both footswitches can be latching or momentary, for instant pitch jumps or quick blasts of echo. The bypass switch can also mute the output in bypass while always listening, to catch, repeat, and manipulate what you just played.
The Raster is designed and assembled in Plymouth, MI, USA.
MORE»
| Price | $329.00 |
The Bitmap(TM) is a stereo bitcrusher with fractional bit reduction and sample rate modulation. The Bitmap 2 adds waveshaping, wavefolding, and a window comparator for extreme digital distortion. A drive control handles everything from single coil guitars to synthesizers, with +8 dBu maximum signal level and plenty of gain with overdrive. Modulation and envelope control create dynamic, responsive distortion and digital artifacts.
The Bitmap 2 is tuned to provide maximum sustain without sputtering on staccato notes. Less extreme settings add layers of nonlinearities that interact in subtle ways, giving you the warmth and grit of 8- and 12-bit samplers. Sample rate reduction turns your guitar into 8-bit video game sounds or twists scales into inharmonic melodies. Sample rate modulation adds subtle motion or morphs your guitar into entirely new textures.
The Bitmap(TM) works with guitar, bass, synthesizers, drum machines, and other instruments or line level sources. A web-based editor allows you to edit presets and access additional parameters and modulation destinations.
Features:
• Fractional bit reduction from 24-bits down to 1-bit
• Sampling rate reduction from 48 kHz down to 110 Hz
• Sample-rate modulation with triangle, square, and random waveforms
• Adjustable wavefolding and waveshaping functions
• Mix control to maintain bass or add subtle crushing
• Envelope control over sampling rate or mix
• Drive control to accommodate single or dual coil pickups and line-level signals
• 4-pole lowpass filter
• Stereo input/output (TRS)
• Soft touch bypass (momentary or latching), user replaceable
• Aux. footswitch assignable to tap tempo or preset selection
• Assignable expression pedal, remote switch, remote tap, or MIDI port
• Additional parameters via MIDI (USB or TRS)
• MIDI clock synchronization
• Presets (4 on front, 127 via MIDI)
• Web-based editor for editing presets and accessing hidden parameters
• Filter cutoff can be modulated by envelope or LFO (via editor, saved to preset)
Designed and assembled in USA. Requires a 9V 250 mA center negative power supply (not included).
MORE»
| Price | $329.00 |
Radius goes far beyond traditional ring modulation. With precise control over the balance and frequency ratios of both sidebands, you'll have more advanced control than with any ring mod that has come before. Organic, complex harmonic structures, bell-like tones, metallic textures, frequency shifting, soft tremolo, and bubbly phaser sounds are all on tap.
Pitch tracking, a push-to-tune footswitch, and picking dynamics make it responsive and predictable in concert. In the studio, Radius has well-spaced controls for tabletop use and a full MIDI implementation for DAW integration. The 24-bit 96 kHz codec, audiophile op amps and stereo input/output make it equally at home in the studio or control room. Radius is a musical ring modulator and frequency shifter that lets you modfy the timbre of your instrument in new ways.
With a multi-waveform LFO, step modulator, and MIDI-playable carrier oscillator, Radius modernizes classic electronic techniques for the future.
Features:
• Stereo ring modulator and frequency shifter
• Continuous mix between ring modulation and frequency shifting
• Selectable 2X frequency ratios for upper and lower sidebands
• Frequency shifting with feedback
• Three carrier frequency ranges (low, high, quantized)
• Carrier frequency pitch tracking (monophonic, +/- 100%)
• Pust-to-tone carrier oscillator
• MIDI-playable carrier oscillator
• Multi-waveform LFO (triangle, square, random, intelligent random, X mod +/-)
• Step modulator (1-8 steps), programmable via front panel
• Tap tempo and MIDI clock sync
• Envelope follower
• Envelope-triggered LFO (one-shot ramp, pulse, random, step mod)
• Configurable AUX switch (tap, tune, preset, LFO)
• USB and TRS MIDI
• Full MIDI implementation
• 96 kHz sampling rate
• Web editor with preset upload/download
• User-installable firmware updates (USB)
Designed and assembled in USA. Requires a 9V DC 250 mA power supply (not included).
MORE»
| Price | $349.00 |
Designed for both acoustic and electric instruments, the Hotone Omni AC is a compact, acoustic simulator pedal that delivers realistic acoustic instrument emulations. These exceptionally authentic sounds are the result of new Black-Tek acoustic simulation technology, which is built on Hotone's CDCM (Comprehensive Dynamic Circuit Modeling) architecture. The Omni AC offers 15 high-quality acoustic simulations, including steel and nylon string guitars, mandolin, acoustic fretless acoustic bass, and classic double basses. A detailed 4-band semi-parametric EQ is included to further tailor the sound. An internal voltage boost circuit provides tons of headroom ensuring the input signal will stay clean, regardless of the instrument's output level. A high-contrast OLED screen makes editing and recalling setting easy in high and low light environments. Omni AC has 15 editable presets which can be adjusted on the pedal or managed via free Mac/PC software. The footswitch can be assigned to bypass the effect or mute the signal. A 1/4″ thru jack provides an unprocessed dry signal to other devices or amplifiers. The pedal includes a 1/4″ output, a balanced XLR out to connect to mixers or audio interfaces, an 1/8″ headphone monitor and an 1/8″ stereo aux input making the Omni AC perfect for both live and recording setups.
Features include:
• Compact, easy-to-use acoustic simulator pedal
• Advanced DSP-powered platform ensures high sound quality
• 24-bit AD/DA conversion, great dynamic response
• Internal voltage boost circuit for exceptional headroom
• 15 high-quality acoustic simulations via Hotone's new Black-Tek modeling
• Detailed 4-band semi-parametric EQ with 12dB maximum boost and cut
• Micro USB jack for updating firmware and loading/managing presets via free Mac/PC software
• 1/4″ input and thruput
• XLR and 1/4″ outputs
• Ground/Lift switch
• 1/8″ stereo Aux In for line level devices (unaffected by Omni AC)
• 1/8″ headphone output for practicing and jamming
• 15 presets
• High-contrast OLED screen
• Assignable footswitch with LED
• 9V DC (center positive) power supply and USB micro cable included
MORE»
| Price | $149.99 |
From light Lo-Fi modulation all the way to the piercing sound of infinity ring-modulation, the Warm Audio RingerBringer accurately recreates the ultimate all-analog ring modulation effect used for experimental tones. With LFO, MOD, FREQ & RATE controls, generate layered frequencies and harmonics, explore a wide range of sonic possibilities for guitar & beyond, and design your own sounds from the ground up. Sporting premium components including hand-selected op-amps and transistors, the RingerBringer delivers true-to-spec performance of the boutique original. The ideal platform for the sonic tinkerer, RingerBringer brings together a distinct set of controls, extensive in/out options, and rich sonic texture to inspire boundless sonic experimentation.
MORE»
| Price | $219.00 |
The Bit Mixer is a small, high-quality mixer designed for pedalboards. It features ultra-low distortion, low noise op amps. High-impedance inputs are designed for guitar, but work with line level signals as well. Each input has a volume knob that goes from off to unity gain. Only 4.4″ x 2.6″, and works with standard pedal power supplies from 9-18 V.
Uses:
• Connect multiple instruments to one amp
• Combine parallel effects chains
• Clean blend or analog dry path
MORE»
| Price | $149.00 |
The Danelectro Honeytone N-10 guitar mini amp cranks like a little hot rod has a great clean or overdriven sound. The Honeytone amp also boasts a real leather handle, belt clip, headphone jack, volume, tone, and overdrive controls. The Honeytone N-10 amp is powered by 9-volt battery (included) or a Danelectro DA-1 adapter.
Features include:
• Great clean and overdrive tones (Best with Polaroid 9V Batteries)
• Leather handle
• Belt clip
• Headphone jack
• Color: Black
MORE»
| List | $39.95 |
| Price | $35.96 (Save: $3.99) |
The Context is a reverb pedal inspired by 1980's rack mount reverbs. It has 8 algorithms, including room, hall, cathedral, gated reverb, reverse reverb, plate, spring, and a granular reverb. Each algorithm features separate high and low frequency damping controls, pre-delay, modulation, dynamics (duck/expand), and infinite hold. In addition, delay is always available, along with tremolo in spring mode.
The modulation knob changes the amount and character of the internal reverb modulation, specific to each algorithm. It gives you a mix of different modulation types from 1980's and early 90's reverbs, including chorus modulation, random modulation that keeps the pitch stable, and deep modulated reverbs. Holding down the shift button adjusts the modulation rate.
Reverse reverb fades in louder and brighter over time, giving the impression of playing backwards. Modulation adds a wash of normal reverb.
The spring reverb was designed using the techniques and algorithms that were used in 1980's reverbs, but with enough DSP power to drip and feel like a spring tank. You can adjust the length of the decay, high and low frequency damping. The modulation is tremolo with adjustable intensity and speed.
Grain mode is a granular reverb inspired by the Ursa Major SST-282 Space Station. The SST-282 was released in 1978 and used multiple delay taps with modulation to create reverb effects. The Context can create ghostly reverb effects, slowly sweeping resonances, and at higher modulation settings is a multi-voice granular processor that creates clouds of detuned sound fragments for entirely new reverb sounds.
When the shift button is held down, the top row of knobs adjust delay parameters. The low and high damping knobs adjust dynamics for ducking reverb or an expander for more reverb on louder notes, with adjustable threshold and recovery time. Holding down the foot switches gives you two different types of infinite sustain.
One preset available on the left footswitch, 4 using a remote footswitch, and 127 via MIDI. The expression pedal can be assigned to any combination of parameters. We also have a web-based editor for tweaking and managing your presets.
Designed and assembled in USA. The Context 2 requires a 9 V 250 mA center negative power supply (not included).
MORE»
| Price | $329.00 |
This pedal will transform your guitar rig!
Don't let the Vertex Boost MKII's name fool you–it's much more than a mere boost. Make no mistake, this multifunction guitar pedal can function as a gain booster, with +16dB of ultra-transparent gain that can either drive your amp into saturation or give your solos a squeaky-clean level bump, depending on where you choose to deploy it. Able to accommodate both line- and instrument-level signals, the Boost MKII also includes ultra-linear input/output buffers that are guaranteed to elevate the sound of your entire rig. This stompbox's buffers can propel a typical mid-level rig into pro-level territory with zero tonal coloration. And if your rig is already 99% of the way there, the Boost MKII will deliver that elusive missing 1%. Beyond that, the Boost MKII's insert jack enables you to adjust your volume via an external treadle-style pedal while keeping your guitar's signal completely isolated–it's like plugging straight into your amp. Boasting a compact enclosure that's 33% slimmer than its predecessor, the Vertex Boost MkII belongs on every tone-obsessed guitarist's pedalboard.
OFFERS MORE THAN +16DB OF EXTRA GAIN WITH ZERO SONIC COLORATION
While the Boost MKII offers a myriad of useful functions, it's a clean booster pedal at heart. Its straightforward Level knob ranges from unity gain to a healthy +16dB. Placing the Boost MKII in front of your amp or dirt boxes adds saturation and sustain to your signal, while placing it after your preamp and dirt boxes gives you a full-range level increase. Best off all, the Boost MKII doesn't change the tone of anything that comes before it's sonically invisible.
INPUT AND OUTPUT BUFFERS OPTIMIZE YOUR SIGNAL PATH FOR MAXIMUM TONE
Guitarists are always searching for new ways to elevate the sound of their rig. Thanks to its top-shelf input and output buffers, the Vertex Boost MKII will do just that. How can a set of buffers transform a noisy, novice-sounding rig into a quiet, pro-level one? For starters, these buffers condition your rig's entire analog signal path, ensuring optimal input and stable output. They also exhibit an unprecedented level of linearity, while ensuring zero coloration of your signal–even with dozens of stompboxes in your chain. The Boost MKII's input buffer compensates for pickups with different impedances, ensuring that both single-coil- and humbucker-equipped guitars retain every ounce of their tone, while its output buffer tackles arena-sized cable runs like a a champ. Got a hissy, interference-prone passive effects loop? Not anymore – the Boost MKII will convert it into a max-quality, whisper-quiet active loop.
CONTROL YOUR VOLUME WITH AN EXTERNAL VOLUME OR EXP PEDAL
On the rear of the Boost MKII, you'll find a 1/8-inch TRS insert. This enables you to control your volume using an external treadle-style pedal. When the Boost
MORE»
| Price | $199.99 |
iRig BlueBoard is the first wireless MIDI pedalboard for iOS and Mac that allows you to control your music apps and more from the floor.
Now control parameters of your MIDI-compatible apps like AmpliTube wirelessly from the floor. Switch between presets, change patches, turn effects on and off and control effects like volume wah pedals all from the stage floor without worrying about tripping over wires. Setup is as simple as turning the iRig BlueBoard on and telling it what you want to control.
iRig BlueBoard features four backlit soft-touch pads housed in a sturdy, stage-worthy chassis, two TRS expansion jacks for connecting additional MIDI controllers like expression pedals, and is powered by four standard AAA batteries.
MORE»
| Price | $119.99 |
The Danelectro Honeytone N-10 guitar mini amp cranks like a little hot rod has a great clean or overdriven sound. The Honeytone amp also boasts a real leather handle, belt clip, headphone jack, volume, tone, and overdrive controls. The Honeytone N-10 amp is powered by 9-volt battery (included) or a Danelectro DA-1 adapter.
Features include:
• Great clean and overdrive tones (Best with Polaroid 9V Batteries)
• Leather handle
• Belt clip
• Headphone jack
• Color: Burgundy
MORE»
| List | $39.95 |
| Price | $35.96 (Save: $3.99) |
iRig BlueBoard is the first wireless MIDI pedalboard for iOS and Mac that allows you to control your music apps and more from the floor.
Now control parameters of your MIDI-compatible apps like AmpliTube wirelessly from the floor. Switch between presets, change patches, turn effects on and off and control effects like volume wah pedals all from the stage floor without worrying about tripping over wires. Setup is as simple as turning the iRig BlueBoard on and telling it what you want to control.
iRig BlueBoard features four backlit soft-touch pads housed in a sturdy, stage-worthy chassis, two TRS expansion jacks for connecting additional MIDI controllers like expression pedals, and is powered by four standard AAA batteries.
MORE»
| Price | $119.99 |
The Warm Audio WarmBender features dedicated selectable circuits for delivering two of the most iconic Tone Bender fuzz tones plus a bonus modern tone in one stomp box. WarmBender's NOS 76 setting brings a cutting, present tone to the front of any band, while the NOS 75 delivers that Mark II Professional-style Bender fuzz tone lauded by all the Riff-Lords of the 60s and 70s. WarmBender is made with 100% through-hole construction using NOS Germanium transistors. WarmBender houses two distinc Germanium fuzz circuits plus a third modern silicon circuit for a more smooth, distortion-like tone. With the added SAG control starving the voltage and the smaller pedal footprint, WarmBender is the ultimate Bender fuzz experience.
MORE»
| Price | $199.00 |
Ampero Control is a compact, sturdy, fully programmableBluetooth MIDI controller, that gives musiciansflexible MIDI-based control via MIDI port, USB jackand Bluetooth. It features 4 footswitches – with eachfootswitch, you can send up to 16 different MIDImessages by different actions. You can also attachexpression pedals or more footswitches to your AmperoControl depending on your needs. Ampero Control supports a wide range of MIDI messages including PC, CC, Note On/Off, and others via MIDI, USB and Bluetooth.
MORE»
| Price | $119.99 |
DC-3h Power Supply for POD Go and more!
MORE»
| List | $59.99 |
| Price | $53.99 (Save: $6.00) |
When it comes to Bluesy cleans and fat lead tones, the Vertex Effects Steel String Supreme (Slight Return Edition) – based on serial #001 of a legendary six-figure Dumble Steel String Singer – is the only tone shaper you'll need in your arsenal. Whether you're front-ending a stage amp with the Supreme expanded all-analog preamp, feeding a little D-style sugar into your Amp Modeler, or even running straight into a Cab Simulator/IR Loader, this pedal is guaranteed to put a smile on your face. Just like the amp it's named after, the Steel String Supreme (Slight Return Edition) is characterized by a fat and glassy tones sound that absolutely marinates signals in tubelike harmonics as you ramp up the gain. The Slight Return Edition's active EQ and Bright/Deep + Rock/Jazz switches add new tone-shaping capabilities from the original SSS and bring you a bit more available top end “glass” and a little more low-end “Snap” to this latest addition to the Steel String family. From subtle fattening and clean compression to full-on overdrive, the Vertex Effects Slight Return Edition is the next best thing to having the real-deal SSS in your rig.
Players like Eric Johnson, John Mayer, and Santana have all sung the praises of a rare 100-watt 6L6 blues machine that achieved legendary status in the mid-1980s. And whether it's the ultimate cleans that you're searching for or a lead tone with slight overdrive but tons of BODY the Vertext Steel String Supreme (Slight Return Version – successor to the Steel String MKI Slight Return Version is packing 500% more tone-shaping potential – faithfully captures that “SSS” (that's “Sparkle, Squish, and Saturation”) magic in a pedalboard-friendly stomp.
MORE»
| Price | $249.99 |
HX One is a powerful stereo effect pedal with intuitive controls that fits onto any pedalboard. Select one of 250+ effects taken from the acclaimed HX family processors and easily adjust the parameters displayed on the OLED screen using the three corresponding knobs. You can also automate parameter changes via the unique Flux controller and trigger them with the Tap/Flux footswitch. Connect an optional expression pedal or two external footswitches for additional control.
HX One also provides adjustable input impedance; a choice of True Bypass or buffered DSP Bypass; MIDI In and Out/Thru connectors; 128 Presets; and a USB-C port for firmware updates and use with the HX One Preset Librarian application. HX One may be powered using the included 9V power supply or most third-party power supplies, making it easy to add to your pedalboard.
Features:
• 250+ effects taken from the HX family processors
• Intuitive controls make selecting and editing effects easy
• Flux Controller for automating parameter changes
• Adjustable input impedance to match your instrument
• Connect an optional expression pedal or 2 external footswitches
• MIDI In, Out/Thru connectors (receives PC and CC messages)
• Stereo I/O with choice of True Bypass or buffered DSP Bypass
• 128 preset slots
• USB-C port for firmware updates and use with HX® One Preset Librarian
• 9V power supply included
MORE»
| List | $391.99 |
| Price | $352.79 (Save: $39.20) |
